Re: Dead PET 2001

I agree. I went there a few times in 2005-2006 and it wasn't the same.
Raw components were hard to find, and the sleek consumer electronics
stuff had moved to mega stores like Bic Camera in other areas of Tokyo. Sad.

-Nate

Philip Lord wrote:
> Yes..I'm quite privileged to have such an electronic mecca just 30mins
> away.
> Unfortunately Akihabara as I once knew it is dead (or at least it's in
> it's death throws). Gone are most of the small 'nook and cranny' stores
> where you could rummage for hours and find all sorts of interesting
> junk. It's now populated by Otaku anime and Cos-play shops and multi
> floor mega stores.
> 
> :-(
> 
> 
> On Aug 13, 2009, at 10:54 AM, Bil Herd wrote:
> 
>> All us old Commodore types used to hit Akihabara whenever we were in
>> Tokyo.  Rumor has it that CBM-J would occasionally run down there to
>> buy a few scoops of 7407's to keep production flowin.
>>
>> Bil
>>
>> -----Original Message-----
>> From: owner-cbm-hackers@ling.gu.se
>> [mailto:owner-cbm-hackers@ling.gu.se] On Behalf Of Philip Lord
>> Sent: Wednesday, August 12, 2009 9:37 PM
>> To: cbm-hackers@ling.gu.se
>> Subject: Re: Dead PET 2001
>>
>> Great!
>> I'm going to race into Akihabara this lunch time and get all the CR3,
>> C11, C12, C13, VR3, VR4, VR5, and VR6 parts.
>> Hopefully I'll have time this weekend to attack the board starting
>> with the CR3 diode.
>>
>> Thanks again for your help, and I'll let you know how I go.
>>
>> Cheers
>> Phil
>>
>>
>>
>> On Aug 12, 2009, at 2:40 PM, William Levak wrote:
>>
>>> On Wed, 12 Aug 2009, Philip Lord wrote:
>>>
>>>> I was just about to say that Pin2 is connected to one of the red
>>>> leads that goes to the capacitor, therefore with the red leads
>>>> disconnected there would be 0V at pin2, but instead I decided to
>>>> test it anyway...I got 0.5VDC!!!! Then I realized what is happening:
>>>>
>>>> When I disconnect the two red leads from the capacitor, but still
>>>> have the two leads connected together the voltage reads 0.5VDC at
>>>> pin4 and pin2. When the red leads are disconnected from the
>>>> capacitor, and also disconnected from each other I get just over
>>>> 8VDC at pin4, and 0VDC at pin2 (as expected).
>>>>
>>>> ...as for a glow from the monitor filliment, I had to turn off all
>>>> the lights to see it, but yes indeed, there is a glow.
>>>
>>> This is good!  This means that the transformer, the big filter
>>> capacitor, and CR1 and CR2 are all good.
>>>
>>> The problem is localized to CR3, C11, C12, C13, VR3, VR4, VR5, or
>>> VR6. One or more of those is bad.  The prime suspect is CR3.  If it
>>> was working, you should see 8V on pin 2.  These diodes get hot when
>>> operating. If it is cold, it is probably open.
>>>
>>> Now would be a good time to remove the circuit board.  Small things,
>>> like paper clips, sometimes get trapped under there, and short
>>> things out.
>>> The screw on the left rear of the board is a ground to the chasis.
>>> The others should not contact any circuits.
>>>
>>> wlevak@sdf.lonestar.org
>>> SDF Public Access UNIX System - http://sdf.lonestar.org
>>>
>>>     Message was sent through the cbm-hackers mailing list
>>
>>
>>       Message was sent through the cbm-hackers mailing list
>>
>> -- 
>> This message has been scanned for viruses and dangerous content by
>> IDSi's  MailScanner.
>>
>>
>>
>>       Message was sent through the cbm-hackers mailing list
> 
> 
>       Message was sent through the cbm-hackers mailing list

-- 
Nate


       Message was sent through the cbm-hackers mailing list