RE: rebuild of 6532 for KIM 1

Hi,

 

I'm using this GODIL to develop: http://shop.trenz-electronic.de/catalog/product_info.php?products_id=633

But OHO also has a version with a XC3S250E

 

I've read in the documentation that they can produce the GODIL with XC3S100E

If ordered by 10.

 

There is also the craignell… but more expensive and less flexible to set GND and VCC

On the GODIL I can place GND / VCC anywhere

 

Actually I’m only trying to get something fully working

Then later I’ll try to optimize.

 

For me the target is the 6530 but my micro kim is using 6532

So I use the 6532 as intermediary target to debug the functionalities.

 

One of the idea is to have several 6530 in the same GODIL 

And select the version with jumpers.

(some pins are still available)

 

I know that the 6530 was used In several commodore product

But for now I only know the one used on the KIM. 

 

 


Device Utilization Summary

[-]


Logic Utilization

Used

Available

Utilization

Note(s)


Number of Slice Flip Flops

83

9,312

1%

 


Number of 4 input LUTs

164

9,312

1%

 


Number of occupied Slices

135

4,656

2%

 


    Number of Slices containing only related logic

135

135

100%

 


    Number of Slices containing unrelated logic

0

135

0%

 


Total Number of 4 input LUTs

182

9,312

1%

 


    Number used as logic

164

 

 

 


    Number used as a route-thru

18

 

 

 


Number of bonded IOBs

38

66

57%

 


Number of RAMB16s

1

20

5%

 


Number of BUFGMUXs

1

24

4%

 


Average Fanout of Non-Clock Nets

4.39

 

 

 

						

 

 

 

 

 

-----Message d'origine-----
De : owner-cbm-hackers@musoftware.de [mailto:owner-cbm-hackers@musoftware.de] De la part de Bil Herd
Envoyé : dimanche 19 mai 2013 23:43
À : cbm-hackers@musoftware.de
Objet : RE: rebuild of 6532 for KIM 1

 

Out of curiosity, what is your target CPLD/FPGA and how many LE Blocks are used?

Bil

 

-----Original Message-----

From:  <mailto:owner-cbm-hackers@musoftware.de> owner-cbm-hackers@musoftware.de

[ <mailto:owner-cbm-hackers@musoftware.de> mailto:owner-cbm-hackers@musoftware.de] On Behalf Of  <mailto:didier@aida.org> didier@aida.org

Sent: Sunday, May 19, 2013 5:40 PM

To:  <mailto:cbm-hackers@musoftware.de> cbm-hackers@musoftware.de

Subject: rebuild of 6532 for KIM 1

 

Hi,

 

I've started to test my vhdl code on a GODIL It is not totally working but some functions works

 

1/ I'm not provoking any crash on the bus :) 2/ the timer is not working properly but runs

 

This problems will be resolved in a few days.

 

But my main problem is the increase in power consumption And an overheating of the regulator of my Kim 1

 

(I'm not yet checked the tensions...)

 

 

From a vhdl for 6532 it is easy to write the vhdl for 6530-xxx

 

But inside a floppy disk is there enough place to place a GODIL ?

Almost 2cm thick...

 

It's also bigger than a DIL component..

 

Is it possible to drain more power from the power supply Without problems ?

 

 

I'll place the file on my web site

Once I've replace the main 6532 of my KIM and be abled To test all the functions (for no I'm using the GODIL on the extension I/O)

 

 

--

didier

 

 

 

 

 

 

       Message was sent through the cbm-hackers mailing list

 

       Message was sent through the cbm-hackers mailing list




       Message was sent through the cbm-hackers mailing list